o: ActiveSupport::Cache::Entry :@compressedF: @value" '"'
main.h
1 
#include <18F4550.h>
1 
#include <16F887.h>
2 2 
#device adc=8
3 3 

  		




  4
  
  
    
#FUSES NOWDT                    //No Watch Dog Timer


  		




  5
  
  
    
#FUSES WDT128                   //Watch Dog Timer uses 1:128 Postscale


  		




  6
  
  
    
#FUSES INTRC                    //Internal RC Osc


  		




  7
  
  
    
#FUSES NOPROTECT                //Code not protected from reading


  		




  8
  
  
    
#FUSES NOBROWNOUT               //No brownout reset


  		




  9
  
  
    
#FUSES BORV20                   //Brownout reset at 2.0V


  		




  10
  
  
    
#FUSES NOPUT                    //No Power Up Timer


  		




  11
  
  
    
#FUSES NOCPD                    //No EE protection


  		




  12
  
  
    
#FUSES STVREN                   //Stack full/underflow will cause reset


  		




  13
  
  
    
#FUSES NODEBUG                  //No Debug mode for ICD


  		




  14
  
  
    
#FUSES NOLVP                    //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O


  		




  15
  
  
    
#FUSES NOWRT                    //Program memory not write protected


  		




  16
  
  
    
#FUSES NOWRTD                   //Data EEPROM not write protected


  		




  17
  
  
    
#FUSES IESO                     //Internal External Switch Over mode enabled


  		




  18
  
  
    
#FUSES FCMEN                    //Fail-safe clock monitor enabled


  		




  19
  
  
    
#FUSES PBADEN                   //PORTB pins are configured as analog input channels on RESET


  		




  20
  
  
    
#FUSES NOWRTC                   //configuration not registers write protected


  		




  21
  
  
    
#FUSES NOWRTB                   //Boot block not write protected


  		




  22
  
  
    
#FUSES NOEBTR                   //Memory not protected from table reads


  		




  23
  
  
    
#FUSES NOEBTRB                  //Boot block not protected from table reads


  		




  24
  
  
    
#FUSES NOCPB                    //No Boot Block code protection


  		




  25
  
  
    
#FUSES MCLR                     //Master Clear pin enabled


  		




  26
  
  
    
#FUSES LPT1OSC                  //Timer1 configured for low-power operation


  		




  27
  
  
    
#FUSES NOXINST                  //Extended set extension and Indexed Addressing mode disabled (Legacy mode)


  		




  28
  
  
    
#FUSES PLL1                     //No PLL PreScaler


  		




  29
  
  
    
#FUSES CPUDIV1                  //No System Clock Postscaler


  		




  30
  
  
    
#FUSES USBDIV                   //USB clock source comes from PLL divide by 2


  		




  31
  
  
    
#FUSES VREGEN                   //USB voltage regulator enabled


  		




  32
  
  
    
#FUSES ICPRT                    //ICPRT enabled


  		




  
  4
  
    
#FUSES WDT                   	//Watch Dog Timer


  		




  
  5
  
    
#FUSES HS                    	//High speed Osc (> 4mhz for PCM/PCH) (>10mhz for PCD)


  		




  
  6
  
    
#FUSES PUT                   	//Power Up Timer


  		




  
  7
  
    
#FUSES MCLR                  	//Master Clear pin enabled


  		




  
  8
  
    
#FUSES NOPROTECT             	//Code not protected from reading


  		




  
  9
  
    
#FUSES NOCPD                 	//No EE protection


  		




  
  10
  
    
#FUSES NOBROWNOUT            	//No brownout reset


  		




  
  11
  
    
#FUSES IESO                  	//Internal External Switch Over mode enabled


  		




  
  12
  
    
#FUSES FCMEN                 	//Fail-safe clock monitor enabled


  		




  
  13
  
    
#FUSES NOLVP                 	//No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O


  		




  
  14
  
    
#FUSES NODEBUG               	//No Debug mode for ICD


  		




  
  15
  
    
#FUSES NOWRT                 	//Program memory not write protected


  		




  
  16
  
    
#FUSES BORV40                	//Brownout reset at 4.0V


  		




  33
  17
  
    

  		




  34
  
  
    
#use delay(clock=8000000)


  		




  35
  
  
    
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8)


  		




  
  18
  
    
#use delay(clock=8000000,RESTART_WDT)


  		




  
  19
  
    
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8,restart_wdt)


  		




  36
  20
  
    

  		










:@created_atf1417828687.7163789Ù':@expires_in0