o: ActiveSupport::Cache::Entry :@compressedF: @value".".
main.h
1 
#include <18F8310.h>
1 
#include <18F4550.h>
2 2 
#device adc=8
3 3 

  		




  4
  4
  
    
#FUSES NOWDT                    //No Watch Dog Timer


  		




  5
  5
  
    
#FUSES WDT128                   //Watch Dog Timer uses 1:128 Postscale


  		




  6
  
  
    
#FUSES INTRC_IO                 //Internal RC Osc, no CLKOUT


  		




  
  6
  
    
#FUSES HS                       //High speed Osc (> 4mhz for PCM/PCH) (>10mhz for PCD)


  		




  
  7
  
    
#FUSES NOPROTECT                //Code not protected from reading


  		




  7
  8
  
    
#FUSES NOBROWNOUT               //No brownout reset


  		




  8
  
  
    
#FUSES BORV46                   //Brownout reset at 4.6V


  		




  9
  
  
    
#FUSES PUT                      //Power Up Timer


  		




  10
  
  
    
#FUSES BW16                     //16-bit external bus mode


  		




  
  9
  
    
#FUSES BORV20                   //Brownout reset at 2.0V


  		




  
  10
  
    
#FUSES NOPUT                    //No Power Up Timer


  		




  
  11
  
    
#FUSES NOCPD                    //No EE protection


  		




  11
  12
  
    
#FUSES STVREN                   //Stack full/underflow will cause reset


  		




  12
  13
  
    
#FUSES NODEBUG                  //No Debug mode for ICD


  		




  13
  
  
    
#FUSES NOIESO                   //Internal External Switch Over mode disabled


  		




  14
  
  
    
#FUSES NOFCMEN                  //Fail-safe clock monitor disabled


  		




  15
  
  
    
#FUSES NOXINST                  //Extended set extension and Indexed Addressing mode disabled (Legacy mode)


  		




  16
  
  
    
#FUSES NOWAIT                   //Wait selections unavailable for Table Reads or Table Writes


  		




  17
  
  
    
#FUSES NOPROTECT                //Code not protected from reading


  		




  
  14
  
    
#FUSES NOLVP                    //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O


  		




  
  15
  
    
#FUSES NOWRT                    //Program memory not write protected


  		




  
  16
  
    
#FUSES NOWRTD                   //Data EEPROM not write protected


  		




  
  17
  
    
#FUSES IESO                     //Internal External Switch Over mode enabled


  		




  
  18
  
    
#FUSES FCMEN                    //Fail-safe clock monitor enabled


  		




  
  19
  
    
#FUSES PBADEN                   //PORTB pins are configured as analog input channels on RESET


  		




  
  20
  
    
#FUSES NOWRTC                   //configuration not registers write protected


  		




  
  21
  
    
#FUSES NOWRTB                   //Boot block not write protected


  		




  18
  22
  
    
#FUSES NOEBTR                   //Memory not protected from table reads


  		




  19
  
  
    
#FUSES NOLPT1OSC                //Timer1 configured for higher power operation


  		




  
  23
  
    
#FUSES NOEBTRB                  //Boot block not protected from table reads


  		




  
  24
  
    
#FUSES NOCPB                    //No Boot Block code protection


  		




  20
  25
  
    
#FUSES MCLR                     //Master Clear pin enabled


  		




  21
  
  
    
#FUSES MCU                      //Microcontroller Mode


  		




  
  26
  
    
#FUSES LPT1OSC                  //Timer1 configured for low-power operation


  		




  
  27
  
    
#FUSES NOXINST                  //Extended set extension and Indexed Addressing mode disabled (Legacy mode)


  		




  
  28
  
    
#FUSES PLL12                    //Divide By 12(48MHz oscillator input)


  		




  
  29
  
    
#FUSES CPUDIV1                  //System Clock by 1


  		




  
  30
  
    
#FUSES USBDIV                   //USB clock source comes from PLL divide by 2


  		




  
  31
  
    
#FUSES VREGEN                   //USB voltage regulator enabled


  		




  
  32
  
    
#FUSES ICPRT                    //ICPRT enabled


  		




  22
  33
  
    

  		




  23
  
  
    
#use delay(clock=1000000)


  		




  24
  
  
    
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8)


  		




  
  34
  
    
#use delay(clock=20000000)


  		




  
  35
  
    
#use rs232(baud=9600,parity=N,xmit=PIN_B7,rcv=PIN_B6,bits=8)


  		




  25
  36
  
    

  		




  
  37
  
    
#define TDC_ENABLE PIN_B3      //enable pin for SPI communication with TDC


  		




  
  38
  
    
#use spi(DI=PIN_B1, DO=PIN_B0, CLK=PIN_B2, stream=TDC_stream, bits=32)   // uses software SPI


  		




  
  39
  
    

  		




  
  40
  
    

  		




  
  41
  
    

  		












  

    
      main.pjt
    
  





  20
  20
  
    
Count=1


  		




  21
  21
  
    
1=C:\Users\kakl\Documents\MLAB\Modules\TDC\GP201A\SW\PICinterface\main


  		




  22
  22
  
    
[Opened Files]


  		




  23
  
  
    
1=..\..\..\..\TDC\GP201A\SW\PICinterface\main.c


  		




  
  23
  
    
1=main.c


  		




  24
  24
  
    
2=main.h


  		




  25
  25
  
    
3=..\..\..\..\..\..\..\..\..\Program Files\PICC\Devices\18F4550.h


  		




  26
  26
  
    
4=GP2.c


  		










:@created_atf1427458263.274394:@expires_in0